Washable water-based odourless enamel for interiors and exteriors.
Washable water-based enamel, based on acrylic resins, pigments and ecologic additives, practically odourless and can be also used in closed and poorly ventilated areas without causing the formation of noxious or annoying odours.
The product is generally ready to use but if it is necessary to reduce the viscosity in certain cases, it can be diluted with water up to a maximum of 10÷12%.
Suitable to use on all types of interior surfaces, as long as they are perfectly clean and dry. On new or never painted surfaces, it is recommended to apply a preparation coat of "CIPIRFOND" or "CIPIRFOND" before applying the water-based enamel.
VOLATILE ORGANIC COMPOUNDS EU limit value VOC (Directive 2004/42 EC) Pitture lucide per pareti e soffitti interni (Cat A/b) BA 100 gr/lt (2013) Smalto inodore all’acqua max contains 100 gr/lt di VOC
Can be diluted with water. Can be mixed with the chart colours.
Store the product at a temperature, no lower than 5°C out of direct sunlight. The product, stored and sealed in the original packages, keeps for a period of 2 (two) years.
On surfaces treated with sealers and/or suitable bases, the product covers 8÷10m²/lt for two coats.
The empty jar and washing residue of the used equipment must be disposed of, according to local regulations in force.
To apply with a brush or roller, dilute at 5÷7%. To apply with a spray, dilute at 8÷10%.
In normal temperature conditions (22°C) and relative humidity (60%), the surface is dry to the touch in 2÷3 hours and can be painted over after 18 hours.
Use at ambient temperatures between 10°C and 30°C. Avoid application in case of strong rain, wind and high sunlight.
CYCLE: On new wooden substrates: make sure the surface is perfectly clean and dry, then sand lightly to remove any small imperfections in the wood. Before applying Smalto inodore all’acqua enamel, it is recommended to treat the surface with a base coat of "CIPIRFOND". Smalto inodore all’acqua can be applied at least 18÷24 hours after.
On already painted wooden substrates: clean the surface, removing any traces of old flaky paint, matt by sanding, dust and then apply a first coat of Smalto inodore all’acqua enamel and after at least 18÷24 hours the second coat of the product can be applied.
On new metal substrates: clean, degrease and remove traces of rust, apply a coat of . After 18÷24 hours apply a first coat of Smalto inodore all’acqua and after a further 24 hours, the second coat.
On already painted metal substrates: clean and matt the surface by sanding, remove traces of rust and then apply a first coat of Smalto inodore all’acqua and after 24 hours, the second coat of product.
On a new wall: fill the imperfections of the wall, sand and brush and then apply a coat of "SOTTOSMALTO". After at least 12 hours, apply a first coat of Smalto inodore all’acqua and then the second one after another 24 hours.
WARNINGS: Mix the product well before use.
NOTE: Ideal ambient conditions: temperature: min. +8°C max. +30°C relative humidity <70%. Ideal substrate conditions: temperature: min. +5°C max. +30°C - humidity <10%. It is recommended to apply the product in favourable climatic conditions as indicated. Applying the product in unsuitable environmental conditions, negatively affects the drying time, compromising the optimal result of both the aesthetic characteristics and its performance.
Do not apply on fresh and alkaline substrates; wait for it to cure (generally four weeks).
Use in a well-ventilated area.
CIPIR ensures that the information is provided to the best of its experience and technical-scientific knowledge; nevertheless, it cannot assume any responsibility for the results obtained as application conditions are beyond its control.